Operations, Administration and Maintenance (OAM) for Deterministic Networks (DetNet) with MPLS Data PlaneEricssongregimirsky@gmail.comHuaweimach.chen@huawei.comEricssonMagyar Tudosok krt. 11.BudapestHungary1117balazs.a.varga@ericsson.com
Routing
DetNet Working GroupInternet-DraftDetNetOAM
This document defines format and use principals of the
Deterministic Network (DetNet) service Associated Channel (ACH) over a DetNet network with the MPLS data plane.
The DetNet service ACH can be used to carry test packets of active Operations, Administration, and Maintenance protocols
that are used to detect DetNet failures and measure performance metrics.
Introduction introduces and explains Deterministic Networks (DetNet)
architecture and how the Packet Replication, Elimination, and Ordering functions (PREOF) can be used to
ensure low packet drop ratio in DetNet domain.
Operations, Administration and Maintenance (OAM) protocols are used to detect, localize defects in the network,
and monitor network performance. Some OAM functions, e.g., failure detection, work in the
network proactively, while others, e.g., defect localization, usually performed on-demand.
These tasks achieved by a combination of active and hybrid, as defined in ,
OAM methods.
Also, this document defines format and use principals of the
DetNet service Associated Channel over a DetNet network with
the MPLS data plane .
Conventions used in this documentTerminology and Acronyms
The term "DetNet OAM" used in this document interchangeably with longer version
"set of OAM protocols, methods and tools for Deterministic Networks".
CW Control WordDetNet Deterministic Networksd-ACH DetNet Associated Channel Headerd-CW DetNet Control WordDNH DetNet HeaderGAL Generic Associated Channel LabelG-ACh Generic Associated ChannelOAM: Operations, Administration and MaintenancePREOF Packet Replication, Elimination, and Ordering FunctionsPW PseudowireRDI Remote Defect IndicationE2E End-to-endCFM Connectivity Fault Management BFD Bidirectional Forwarding DetectionTSN Time-Sensitive NetworkF-Label A Detnet "forwarding" label that identifies the LSP
used to forward a DetNet flow across an MPLS PSN, e.g.,
a hop-by-hop label used between label switching routers
(LSR).S-Label A DetNet "service" label that is used between DetNet
nodes that implement also the DetNet service sub-layer
functions. An S-Label is also used to identify a
DetNet flow at DetNet service sub-layer. Underlay Network or Underlay Layer: The network that provides
connectivity between the DetNet nodes. MPLS network providing LSP
connectivity between DetNet nodes is an example of the underlay layer.DetNet Node - a node that is an actor in the DetNet domain. DetNet
domain edge node and node that performs PREOF within the domain are
examples of DetNet node.Keywords
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED",
"MAY", and "OPTIONAL" in this document are to be interpreted as
described in BCP 14
when, and only when, they appear in all capitals, as shown here.
Active OAM for DetNet Networks with MPLS Data Plane
OAM protocols and mechanisms act within the data plane of the particular networking layer. And thus it is critical that the data plane encapsulation
supports OAM mechanisms in such a way to comply with the OAM requirements listed in .
One of such examples that require special consideration is requirement #5:
DetNet OAM packets MUST be in-band, i.e., follow precisely the same
path as DetNet data plane traffic both for unidirectional and bi-directional DetNet paths.
The Det Net data plane encapsulation in transport network with MPLS encapsulation specified
in . For the MPLS underlay network, DetNet flows to be encapsulated
analogous to pseudowires (PW) over MPLS packet switched network, as described in ,
. Generic PW MPLS Control Word (CW),
defined in , for DetNet displayed in .
PREOF in the DetNet domain composed by a combination of nodes that perform replication and elimination functions.
The elimination function always uses the S-Label and packet sequencing information, e.g., the value in the Sequence Number field
of DetNet CW (d-CW). The replication sub-function uses the S-Label information only.
For data packets presents an example of PREOF in DetNet domain.
DetNet Active OAM Encapsulation
DetNet OAM, like PW OAM, uses PW Associated Channel Header defined in .
displays the encapsulation of a DetNet
MPLS active OAM packet.
displays encapsulation of a test packet of an active DetNet OAM protocol
in case of MPLS-over-UDP/IP .
displays the format of the DetNet Associated Channel Header (d-ACH).
The d-ACH encodes the following fields:
Bits 0..3 MUST be 0b0001. This value of the first nibble allows the packet to be distinguished
from an IP packet and a DetNet data packet .
Version - is a four-bits field, and the value is the version number of the d-ACH. This specification defines version 0x1.
Sequence Number - is an unsigned eight-bit field. The
sequence number space is circular with no restriction on the
initial value. The originator DetNet node MUST set the value of
the Sequence Number field before the transmission of a packet.
The originator node MUST increase the value of the Sequence Number
field by 1 for each active OAM packet.
Channel Type - contains the value of DetNet Associated Channel Type.
It is one of the values defined in the IANA PW Associated Channel Type registry.
Node ID - is an unsigned 20 bits-long field.
The value of the Node ID field identifies the DetNet node that originated the packet.
Methods of distributing Node ID are outside the scope of this specification.
Level - is a three-bits field.
Flags - is a five-bits field. Flags field contains five one-bit flags.
creates an IANA registry for new flags to be defined. Flags defined in this specification presented in .
U: Unused and for future use. MUST be 0 on transmission and ignored on receipt.
Session ID is a four-bits field.
The DetNet flow, according to , is identified by the S-label that MUST be at the bottom
of the stack. Active OAM packet MUST include d-ACH immediately following the S-label.
DetNet Packet Replication, Elimination, and Ordering Functions Interaction with Active OAM
At the DetNet service sub-layer, special functions MAY be applied
to the particular DetNet flow, PREOF, to potentially lower packet loss, improve the probability of on-time packet delivery
and ensure in-order packet delivery.
PREOF rely on sequencing information in the DetNet service sub-layer. For a DetNet active OAM packet,
28 MSBs of the d-ACH MUST be used
as the source of the sequencing information by PREOF.
Use of Hybrid OAM in DetNetHybrid OAM methods are used in performance monitoring and defined in as:
Hybrid Methods are Methods of Measurement that use a combination of
Active Methods and Passive Methods.
A hybrid measurement method may produce metrics as close to passive,
but it still alters something in a data packet even if that is the value of a
designated field in the packet encapsulation. One example of such a hybrid measurement method
is the Alternate Marking method described in . Reserving the
field for the Alternate Marking method in the DetNet Header will enhance available to an operator
set of DetNet OAM tools.
OAM Interworking Models
Interworking of two OAM domains that utilize different networking technology can be realized either by a peering or a tunneling model.
In a peering model, OAM domains are within the corresponding network domain.
When using the peering model, state changes that are detected by a Fault Management OAM protocol
can be mapped from one OAM domain into another or a notification, e.g., an alarm, can be sent to a central controller.
In the tunneling model of OAM interworking, usually, only one active OAM protocol is used. Its test packets
are tunneled through another domain along with the data flow, thus ensuring the fate sharing among test and data packets.
OAM of DetNet MPLS Interworking with OAM of TSN
Active DetNet OAM is required to provide the E2E fault management and performance monitoring for
a DetNet flow. Interworking of DetNet active OAM with MPLS data plane with the
IEEE 802.1 Time-Sensitive Networking (TSN) domain based on .
In the case of the peering model is used in the fault management OAM, then the node that borders both TSN
and DetNet MPLS domains MUST support .
specified the mapping of defect states between Ethernet
Attachment Circuits (ACs) and associated Ethernet PWs that are part of an end-to-end (E2E) emulated Ethernet
service. Requirements and mechanisms described in are equally applicable
to using the peering model to achieve E2E FM OAM over DetNet MPLS and TSN domains.
The Connectivity Fault Management (CFM) protocol or
in can provide fast detection of a failure in the TSN segment of the DetNet service.
In the DetNet MPLS domain BFD (Bidirectional Forwarding Detection), specified in and ,
can be used. To provide E2E failure detection, the TSN segment might be presented as a concatenated with the DetNet MPLS and
the Section 6.8.17 MAY be used to inform the upstream DetNet MPLS node of a failure of the TSN segment.
Performance monitoring can be supported by in the DetNet MPLS and in the TSN domains, respectively.
Performance objectives for each domain should refer to metrics that additive or be defined for each domain separately.
The following considerations are to be realized when using the tunneling model of OAM interworking between DetNet MPLS and TSN domains:
Active OAM test packet MUST be mapped to the same TSN Stream ID as the monitored DetNet flow.
Active OAM test packets MUST be treated in the TSN domain based on its S-label and CoS marking (TC field value).
Note that the tunneling model of the OAM interworking requires that the remote peer of
the E2E OAM domain supports the active OAM protocol selected on the ingress endpoint.
For example, if BFD is used for proactive path continuity monitoring
in the DetNet MPLS domain, a TSN endpoint of the DetNet service has also support BFD as defined in .
OAM of DetNet MPLS Interworking with OAM of DetNet IP
Interworking between active OAM segments in DetNet MPLS and DetNet IP domains can also be realized
using either the peering or the tunneling model, as discussed in . Using the same protocol, e.g., BFD,
over both segments, simplifies the mapping of errors in the peering model. To provide the performance monitoring over a DetNet IP domain
STAMP and its extensions can be used.
IANA ConsiderationsDetNet MPLS OAM Flags Registry
This document describes a new IANA-managed registry to identify DetNet MPLS OAM Flags Bits. The
registration procedure is "IETF Review" .
The registry name is "DetNet MPLS OAM Flags". There are five flags in the five-bit Flags field, defined as in .
DetNet MPLS OAM Flags
Bit
Description
Reference
0-4
Unassigned
This document
Security Considerations
Additionally, security considerations discussed in DetNet specifications: ,
, are applicable to this document.
Security concerns and issues related to MPLS OAM tools like LSP Ping ,
BFD over PW also apply to this specification.
Acknowledgment
Authors extend their appreciation to Pascal Thubert for his insightful comments and productive discussion
that helped to improve the document. The authors are enormously grateful to Janos Farcas for his detailed
comments and the inspiring discussion that made this document clearer and stronger.
ReferencesNormative ReferencesInformational ReferencesConnectivity Fault Management clause of IEEE 802.1QIEEEOAM functions and mechanisms for Ethernet based NetworksITU-T