Internet-Draft whip July 2022
Murillo & Gouaillard Expires 26 January 2023 [Page]
Workgroup:
wish
Internet-Draft:
draft-ietf-wish-whip-04
Published:
Intended Status:
Standards Track
Expires:
Authors:
S. Murillo
Millicast
A. Gouaillard
CoSMo Software

WebRTC-HTTP ingestion protocol (WHIP)

Abstract

This document describes a simple HTTP-based protocol that will allow WebRTC-based ingestion of content into streaming services and/or CDNs.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 26 January 2023.

Table of Contents

1. Introduction

While WebRTC has been very successful in a wide range of scenarios, its adoption in the broadcasting/streaming industry is lagging behind.

The IETF RTCWEB working group standardized JSEP ([RFC8829]), a mechanism used to control the setup, management, and teardown of a multimedia session. It also describes how to negotiate media flows using the Offer/Answer Model with the Session Description Protocol (SDP) [RFC3264] as well as the formats for data sent over the wire (e.g., media types, codec parameters, and encryption). WebRTC intentionally does not specify a signaling transport protocol at application level. This flexibility has allowed the implementation of a wide range of services. However, those services are typically standalone silos which don't require interoperability with other services or leverage the existence of tools that can communicate with them.

In the broadcasting/streaming world, the use of hardware encoders that make it very simple to plug in cables carrying raw media, encode it in-place, and push it to any streaming service or CDN ingest is already ubiquitous. The adoption of a custom signaling transport protocol for each WebRTC service has hindered broader adoption as an ingestion protocol.

While some standard signaling protocols are available that can be integrated with WebRTC, like SIP [RFC3261] or XMPP [RFC6120], they are not designed to be used in broadcasting/streaming services, and there also is no sign of adoption in that industry. RTSP [RFC7826], which is based on RTP and may be the closest in terms of features to WebRTC, is not compatible with the SDP offer/answer model [RFC3264].

So, currently, there is no standard protocol designed for ingesting media into a streaming service using WebRTC and so content providers still rely heavily on protocols like RTMP for doing so. Most of those protocols are not RTP based, requiring media protocol translation when doing egress via WebRTC. Avoiding this media protocol translation is desirable as there is no functional parity between those protocols and WebRTC and it increases the implementation complexity at the media server side.

Also, the media codecs used in those protocols tend to be limited and not negotiated, not always matching the mediac codes supported in WebRTC. This requires transcoding on the ingest node, which introduces delay, degrades media quality and increases the processing workload required on the server side. Server side transcoding that has traditionally been done to present multiple renditions in Adaptive Bit Rate Streaming (ABR) implementations can be replaced with Simulcast [RFC8853] and SVC codecs that are well supported by WebRTC clients. In addition, WebRTC clients can adjust client-side encoding parameters based on RTCP feedback to maximize encoding quality.

This document proposes a simple protocol for supporting WebRTC as media ingestion method which:

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

3. Overview

The WebRTC-HTTP Ingest Protocol (WHIP) uses an HTTP POST request to perform a single-shot SDP offer/answer so an ICE/DTLS session can be established between the encoder/media producer (WHIP client) and the broadcasting ingestion endpoint (Media Server).

Once the ICE/DTLS session is set up, the media will flow unidirectionally from the encoder/media producer (WHIP client) to the broadcasting ingestion endpoint (Media Server). In order to reduce complexity, no SDP renegotiation is supported, so no tracks or streams can be added or removed once the initial SDP offer/answer over HTTP is completed.


 +-------------+    +---------------+ +--------------+ +---------------+
 | WHIP client |    | WHIP endpoint | | Media Server | | WHIP Resource |
 +--+----------+    +---------+-----+ +------+-------+ +--------|------+
    |                         |              |                  |
    |                         |              |                  |
    |HTTP POST (SDP Offer)    |              |                  |
    +------------------------>+              |                  |
    |201 Created (SDP answer) |              |                  |
    +<------------------------+              |                  |
    |          ICE REQUEST                   |                  |
    +--------------------------------------->+                  |
    |          ICE RESPONSE                  |                  |
    |<---------------------------------------+                  |
    |          DTLS SETUP                    |                  |
    |<======================================>|                  |
    |          RTP/RTCP FLOW                 |                  |
    +<-------------------------------------->+                  |
    | HTTP DELETE                                               |
    +---------------------------------------------------------->+
    | 200 OK                                                    |
    <-----------------------------------------------------------x

Figure 1: WHIP session setup and teardown

4. Protocol Operation

In order to set up an ingestion session, the WHIP client will generate an SDP offer according to the JSEP rules and perform an HTTP POST request to the configured WHIP endpoint URL.

The HTTP POST request will have a content type of "application/sdp" and contain the SDP offer as the body. The WHIP endpoint will generate an SDP answer and return a "201 Created" response with a content type of "application/sdp", the SDP answer as the body, and a Location header field pointing to the newly created resource.

The SDP offer SHOULD use the "sendonly" attribute and the SDP answer MUST use the "recvonly" attribute.

POST /whip/endpoint HTTP/1.1
Host: whip.example.com
Content-Type: application/sdp
Content-Length: 1326

v=0
o=- 5228595038118931041 2 IN IP4 127.0.0.1
s=-
t=0 0
a=group:BUNDLE 0 1
a=extmap-allow-mixed
a=msid-semantic: WMS
m=audio 9 UDP/TLS/RTP/SAVPF 111
c=IN IP4 0.0.0.0
a=rtcp:9 IN IP4 0.0.0.0
a=ice-ufrag:zjkk
a=ice-pwd:bP+XJMM09aR8AiX1jdukzR6Y
a=ice-options:trickle
a=fingerprint:sha-256 DA:7B:57:DC:28:CE:04:4F:31:79:85:C4:31:67:EB:27:58:29:ED:77:2A:0D:24:AE:ED:AD:30:BC:BD:F1:9C:02
a=setup:actpass
a=mid:0
a=bundle-only
a=extmap:4 urn:ietf:params:rtp-hdrext:sdes:mid
a=sendonly
a=msid:- d46fb922-d52a-4e9c-aa87-444eadc1521b
a=rtcp-mux
a=rtpmap:111 opus/48000/2
a=fmtp:111 minptime=10;useinbandfec=1
m=video 9 UDP/TLS/RTP/SAVPF 96 97
c=IN IP4 0.0.0.0
a=rtcp:9 IN IP4 0.0.0.0
a=ice-ufrag:zjkk
a=ice-pwd:bP+XJMM09aR8AiX1jdukzR6Y
a=ice-options:trickle
a=fingerprint:sha-256 DA:7B:57:DC:28:CE:04:4F:31:79:85:C4:31:67:EB:27:58:29:ED:77:2A:0D:24:AE:ED:AD:30:BC:BD:F1:9C:02
a=setup:actpass
a=mid:1
a=bundle-only
a=extmap:4 urn:ietf:params:rtp-hdrext:sdes:mid
a=extmap:10 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
a=extmap:11 urn:ietf:params:rtp-hdrext:sdes:repaired-rtp-stream-id
a=sendonly
a=msid:- d46fb922-d52a-4e9c-aa87-444eadc1521b
a=rtcp-mux
a=rtcp-rsize
a=rtpmap:96 VP8/90000
a=rtcp-fb:96 ccm fir
a=rtcp-fb:96 nack
a=rtcp-fb:96 nack pli
a=rtpmap:97 rtx/90000
a=fmtp:97 apt=96

HTTP/1.1 201 Created
ETag: "38sdf4fdsf54:EsAw"
Content-Type: application/sdp
Content-Length: 1400
Location: https://whip.example.com/resource/id

v=0
o=- 1657793490019 1 IN IP4 127.0.0.1
s=-
t=0 0
a=group:BUNDLE 0 1
a=extmap-allow-mixed
a=ice-lite
a=msid-semantic: WMS *
m=audio 9 UDP/TLS/RTP/SAVPF 111
c=IN IP4 0.0.0.0
a=rtcp:9 IN IP4 0.0.0.0
a=ice-ufrag:526be20a538ee422
a=ice-pwd:2e13dde17c1cb009202f627fab90cbec358d766d049c9697
a=fingerprint:sha-256 F7:EB:F3:3E:AC:D2:EA:A7:C1:EC:79:D9:B3:8A:35:DA:70:86:4F:46:D9:2D:CC:D0:BC:81:9F:67:EF:34:2E:BD
a=candidate:1 1 UDP 2130706431 198.51.100.1 39132 typ host
a=setup:passive
a=mid:0
a=bundle-only
a=extmap:4 urn:ietf:params:rtp-hdrext:sdes:mid
a=recvonly
a=rtcp-mux
a=rtcp-rsize
a=rtpmap:111 opus/48000/2
a=fmtp:111 minptime=10;useinbandfec=1
m=video 9 UDP/TLS/RTP/SAVPF 96 97
c=IN IP4 0.0.0.0
a=rtcp:9 IN IP4 0.0.0.0
a=ice-ufrag:526be20a538ee422
a=ice-pwd:2e13dde17c1cb009202f627fab90cbec358d766d049c9697
a=fingerprint:sha-256 F7:EB:F3:3E:AC:D2:EA:A7:C1:EC:79:D9:B3:8A:35:DA:70:86:4F:46:D9:2D:CC:D0:BC:81:9F:67:EF:34:2E:BD
a=candidate:1 1 UDP 2130706431 198.51.100.1 39132 typ host
a=setup:passive
a=mid:1
a=bundle-only
a=extmap:4 urn:ietf:params:rtp-hdrext:sdes:mid
a=extmap:10 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
a=extmap:11 urn:ietf:params:rtp-hdrext:sdes:repaired-rtp-stream-id
a=recvonly
a=rtcp-mux
a=rtcp-rsize
a=rtpmap:96 VP8/90000
a=rtcp-fb:96 ccm fir
a=rtcp-fb:96 nack
a=rtcp-fb:96 nack pli
a=rtpmap:97 rtx/90000
a=fmtp:97 apt=96
Figure 2: HTTP POST doing SDP O/A example

Once a session is setup, ICE consent freshness [RFC7675] will be used to detect abrupt disconnection and DTLS teardown for session termination by either side.

To explicitly terminate a session, the WHIP client MUST perform an HTTP DELETE request to the resource URL returned in the Location header field of the initial HTTP POST. Upon receiving the HTTP DELETE request, the WHIP resource will be removed and the resources freed on the Media Server, terminating the ICE and DTLS sessions.

A Media Server terminating a session MUST follow the procedures in [RFC7675] section 5.2 for immediate revocation of consent.

The WHIP endpoints MUST return an HTTP 405 response for any HTTP GET, HEAD or PUT requests on the resource URL in order to reserve its usage for future versions of this protocol specification.

The WHIP resources MUST return an HTTP 405 response for any HTTP GET, HEAD, POST or PUT requests on the resource URL in order to reserve its usage for future versions of this protocol specification.

4.1. ICE and NAT support

The initial offer by the WHIP client MAY be sent after the full ICE gathering is complete with the full list of ICE candidates, or it MAY only contain local candidates (or even an empty list of candidates).

In order to simplify the protocol, there is no support for exchanging gathered trickle candidates from Media Server ICE candidates once the SDP answer is sent. The WHIP Endpoint SHALL gather all the ICE candidates for the Media Server before responding to the client request and the SDP answer SHALL contain the full list of ICE candidates of the Media Server. The Media Server MAY use ICE lite, while the WHIP client MUST implement full ICE.

The WHIP client MAY perform trickle ICE or ICE restarts [RFC8863] by sending an HTTP PATCH request to the WHIP resource URL with a body containing a SDP fragment with MIME type "application/trickle-ice-sdpfrag" as specified in [RFC8840]. When used for trickle ICE, the body of this PATCH message will contain the new ICE candidate; when used for ICE restarts, it will contain a new ICE ufrag/pwd pair.

Trickle ICE and ICE restart support is OPTIONAL for a WHIP resource. If both Trickle ICE or ICE restarts are not supported by the WHIP resource, it MUST return a 405 Method Not Allowed response for any HTTP PATCH request. If the WHIP resource supports either Trickle ICE or ICE restarts, but not both, it MUST return a 501 Not Implemented for the HTTP PATCH requests that are not supported.

As the HTTP PATCH request sent by a WHIP client may be received out-of-order by the WHIP resource, the WHIP resource MUST generate a unique strong entity-tag identifying the ICE session as per [RFC9110] section 2.3. The initial value of the entity-tag identifying the initial ICE session MUST be returned in an ETag header field in the 201 response to the initial POST request to the WHIP endpoint. It MUST also be returned in the 200 OK of any PATCH request that triggers an ICE restart.

A WHIP client sending a PATCH request for performing trickle ICE MUST include an "If-Match" header field with the latest known entity-tag as per [RFC9110] section 3.1. When the PATCH request is received by the WHIP resource, it MUST compare the indicated entity-tag value with the current entity-tag of the resource as per [RFC9110] section 3.1 and return a "412 Precondition Failed" response if they do not match.

WHIP clients SHOULD NOT use entity-tag validation when matching a specific ICE session is not required, such as for example when initiating a DELETE request to terminate a session.

A WHIP resource receiving a PATCH request with new ICE candidates, but which does not perform an ICE restart, MUST return a "204 No Content" response without body. If the Media Server does not support a candidate transport or is not able to resolve the connection address, it MUST accept the HTTP request with the 204 response and silently discard the candidate.

PATCH /resource/id HTTP/1.1
Host: whip.example.com
If-Match: "38sdf4fdsf54:EsAw"
Content-Type: application/trickle-ice-sdpfrag
Content-Length: 548

a=ice-ufrag:EsAw
a=ice-pwd:P2uYro0UCOQ4zxjKXaWCBui1
m=audio RTP/AVP 0
a=mid:0
a=candidate:1387637174 1 udp 2122260223 192.0.2.1 61764 typ host generation 0 ufrag EsAw network-id 1
a=candidate:3471623853 1 udp 2122194687 198.51.100.1 61765 typ host generation 0 ufrag EsAw network-id 2
a=candidate:473322822 1 tcp 1518280447 192.0.2.1 9 typ host tcptype active generation 0 ufrag EsAw network-id 1
a=candidate:2154773085 1 tcp 1518214911 198.51.100.2 9 typ host tcptype active generation 0 ufrag EsAw network-id 2
a=end-of-candidates

HTTP/1.1 204 No Content
Figure 3: Trickle ICE request

A WHIP client sending a PATCH request for performing ICE restart MUST contain an "If-Match" header field with a field-value "*" as per [RFC9110] section 3.1.

If the HTTP PATCH request results in an ICE restart, the WHIP resource SHALL return a "200 OK" with an "application/trickle-ice-sdpfrag" body containing the new ICE username fragment and password. The response may optionally contain the new set of ICE candidates for the Media Server and the new entity-tag correspond to the new ICE session in an ETag response header field.

If the ICE request cannot be satisfied by the WHIP resource, the resource MUST return an appropriate HTTP error code and MUST NOT terminate the session immediately. The WHIP client MAY retry performing a new ICE restart or terminate the session by issuing an HTTP DELETE request instead. In either case, the session MUST be terminated if the ICE consent expires as a consequence of the failed ICE restart as per [RFC7675] section 5.1.

PATCH /resource/id HTTP/1.1
Host: whip.example.com
If-Match: "*"
Content-Type: application/trickle-ice-sdpfrag
Content-Length: 54

a=ice-ufrag:ysXw
a=ice-pwd:vw5LmwG4y/e6dPP/zAP9Gp5k

HTTP/1.1 200 OK
ETag: "289b31b754eaa438:ysXw"
Content-Type: application/trickle-ice-sdpfrag
Content-Length: 102

a=ice-lite
a=ice-ufrag:289b31b754eaa438
a=ice-pwd:0b66f472495ef0ccac7bda653ab6be49ea13114472a5d10a
Figure 4: ICE restart request

Because the WHIP client needs to know the entity-tag associated with the ICE session in order to send new ICE candidates, it MUST buffer any gathered candidates before it receives the HTTP response to the initial POST request or the PATCH request with the new entity-tag value. Once it knows the entity-tag value, the WHIP client SHOULD send a single aggregated HTTP PATCH request with all the ICE candidates it has buffered so far.

In case of unstable network conditions, the ICE restart HTTP PATCH requests and responses might be received out of order. In order to mitigate this scenario, when the client performs an ICE restart, it MUST discard any previous ice username/pwd frags and ignore any further HTTP PATCH response received from a pending HTTP PATCH request. Clients MUST apply only the ICE information received in the response to the last sent request. If there is a mismatch between the ICE information at the client and at the server (because of an out-of-order request), the STUN requests will contain invalid ICE information and will be rejected by the server. When this situation is detected by the WHIP Client, it SHOULD send a new ICE restart request to the server.

4.2. WebRTC constraints

In the specific case of media ingestion into a streaming service, some assumptions can be made about the server-side which simplifies the WebRTC compliance burden, as detailed in WebRTC-gateway document [I-D.draft-ietf-rtcweb-gateways].

In order to reduce the complexity of implementing WHIP in both clients and Media Servers, WHIP imposes the following restrictions regarding WebRTC usage:

Both the WHIP client and the WHIP endpoint SHALL use SDP bundle [RFC9143]. Each "m=" section MUST be part of a single BUNDLE group. Hence, when a WHIP client sends an SDP offer, it MUST include a "bundle-only" attribute in each bundled "m=" section. The WHIP client and the Media Server MUST support multiplexed media associated with the BUNDLE group as per [RFC9143] section 9. In addition, per [RFC9143] the WHIP client and Media Server will use RTP/RTCP multiplexing for all bundled media. The WHIP client and Media Server SHOULD include the "rtcp-mux-only" attribute in each bundled "m=" sections.

While this version of the specification only supports a single audio and video track, in order to ensure forward compatibility, if the number of audio and or video tracks or number streams is not supported by the WHIP Endpoint, it MUST reject the HTTP POST request with a 406 Not Acceptable error code.

Furthermore, the WHIP Endpoint SHOULD NOT reject individual "m=" sections as per [RFC8829] section 5.3.1 in case there is any error processing the "m=" section, but reject the HTTP POST request with a 406 Not Acceptable error code to prevent having partially successful WHIP sessions.

When a WHIP client sends an SDP offer, it SHOULD insert an SDP "setup" attribute with an "actpass" attribute value, as defined in [RFC8842]. However, if the WHIP client only implements the DTLS client role, it MAY use an SDP "setup" attribute with an "active" attribute value. If the WHIP endpoint does not support an SDP offer with an SDP "setup" attribute with an "active" attribute value, it SHOULD reject the request with a 422 Unprocessable Entity response.

NOTE: [RFC8842] defines that the offerer must insert an SDP "setup" attribute with an "actpass" attribute value. However, the WHIP client will always communicate with a Media Server that is expected to support the DTLS server role, in which case the client might choose to only implement support for the DTLS client role.

Tricke ICE and ICE restarts support is OPTIONAL for both the WHIP clients and Media Servers as explained in section 4.1.

4.3. Load balancing and redirections

WHIP endpoints and Media Servers might not be colocated on the same server, so it is possible to load balance incoming requests to different Media Servers. WHIP clients SHALL support HTTP redirection via the "307 Temporary Redirect response code" as described in [RFC9110] section 6.4.7. The WHIP resource URL MUST be a final one, and redirections are not required to be supported for the PATCH and DELETE requests sent to it.

In case of high load, the WHIP endpoints MAY return a 503 (Service Unavailable) status code indicating that the server is currently unable to handle the request due to a temporary overload or scheduled maintenance, which will likely be alleviated after some delay. The WHIP endpoint might send a Retry-After header field indicating the minimum time that the user agent ought to wait before making a follow-up request.

4.4. STUN/TURN server configuration

The WHIP endpoint MAY return STUN/TURN server configuration URLs and credentials usable by the client in the "201 Created" response to the HTTP POST request to the WHIP endpoint URL.

Each STUN/TURN server will be returned using the "Link" header field [RFC8288] with a "rel"" attribute value of "ice-server". The Link target URI is the server URL as defined in [RFC7064] and [RFC7065]. The credentials are encoded in the Link target attributes as follows:

  • username: If the Link header field represents a TURN server, and credential-type is "password", then this attribute specifies the username to use with that TURN server.
  • credential: If the "credential-type" attribute is missing or has a "password" value, the credential attribute represents a long-term authentication password, as described in [RFC8489], Section 10.2.
  • credential-type: If the Link header field represents a TURN server, then this attribute specifies how the credential attribute value should be used when that TURN server requests authorization. The default value if the attribute is not present is "password".
     Link: <stun:stun.example.net>; rel="ice-server"
     Link: <turn:turn.example.net?transport=udp>; rel="ice-server";
           username="user"; credential="myPassword"; credential-type="password"
     Link: <turn:turn.example.net?transport=tcp>; rel="ice-server";
           username="user"; credential="myPassword"; credential-type="password"
     Link: <turns:turn.example.net?transport=tcp>; rel="ice-server";
           username="user"; credential="myPassword"; credential-type="password"
Figure 5: Example ICE server configuration

NOTE: The naming of both the "rel" attribute value of "ice-server" and the target attributes follows the one used on the W3C WebRTC recommendation [W3C.REC-webrtc-20210126] RTCConfiguration dictionary in section 4.2.1. "rel" attribute value of "ice-server" is not prepended with the "urn:ietf:params:whip:" so it can be reused by other specifications which may use this mechanism to configure the usage of STUN/TURN servers.

There are some WebRTC implementations that do not support updating the STUN/TURN server configuration after the local offer has been created as specified in [RFC8829] section 4.1.18. In order to support these clients, the WHIP endpoint MAY also include the STUN/TURN server configuration on the responses to OPTIONS request sent to the WHIP endpoint URL before the POST request is sent.

The generation of the TURN server credentials may require performing a request to an external provider, which can both add latency to the OPTION request processing and increase the processing required to handle that request. In order to prevent this, the WHIP Endpoint SHOULD NOT return the STUN/TURN server configuration if the OPTION request is a preflight request for CORS, that is, if The OPTION request does not contain an Access-Control-Request-Method with "POST" value and the the Access-Control-Request-Headers HTTP header does not contain the "Link" value.

It might be also possible to configure the STUN/TURN server URLs with long term credentials provided by either the broadcasting service or an external TURN provider on the WHIP client, overriding the values provided by the WHIP endpoint.

4.5. Authentication and authorization

WHIP endpoints and resources MAY require the HTTP request to be authenticated using an HTTP Authorization header field with a Bearer token as specified in [RFC6750] section 2.1. WHIP clients MUST implement this authentication and authorization mechanism and send the HTTP Authorization header field in all HTTP requests sent to either the WHIP endpoint or resource except the preflight OPTIONS requests for CORS.

WHIP endpoints and resources MAY require the HTTP request to be authenticated using an HTTP Authorization header field with a Bearer token as specified in [RFC6750] section 2.1. WHIP clients MUST implement this authentication and authorization mechanism and send the HTTP Authorization header field in all HTTP requests sent to either the WHIP endpoint or resource.

The nature, syntax, and semantics of the bearer token, as well as how to distribute it to the client, is outside the scope of this document. Some examples of the kind of tokens that could be used are, but are not limited to, JWT tokens as per [RFC6750] and [RFC8725] or a shared secret stored on a database. The tokens are typically made available to the end user alongside the WHIP endpoint URL and configured on the WHIP clients (similar to the way RTMP URLs and Stream Keys are distributed).

WHIP endpoints and resources could perform the authentication and authorization by encoding an authentication token within the URLs for the WHIP endpoints or resources instead. In case the WHIP client is not configured to use a bearer token, the HTTP Authorization header field must not be sent in any request.

4.6. Simulcast and scalable video coding

Both Simulcast [RFC8853] and Scalable Video Coding (SVC), including K-SVC (also known as "S modes", in which multiple encodings are sent on the same SSRC), MAY be supported by both the Media Servers and WHIP clients through negotiation in the SDP offer/answer.

If the client supports simulcast and wants to enable it for publishing, it MUST negotiate the support in the SDP offer according to the procedures in [RFC8853] section 5.3. A server accepting a simulcast offer MUST create an answer according to the procedures [RFC8853] section 5.3.2.

4.7. Protocol extensions

In order to support future extensions to be defined for the WHIP protocol, a common procedure for registering and announcing the new extensions is defined.

Protocol extensions supported by the WHIP server MUST be advertised to the WHIP client in the "201 Created" response to the initial HTTP POST request sent to the WHIP endpoint. The WHIP endpoint MUST return one "Link" header field for each extension, with the extension "rel" type attribute and the URI for the HTTP resource that will be available for receiving requests related to that extension.

Protocol extensions are optional for both WHIP clients and servers. WHIP clients MUST ignore any Link attribute with an unknown "rel" attribute value and WHIP servers MUST NOT require the usage of any of the extensions.

Each protocol extension MUST register a unique "rel" attribute value at IANA starting with the prefix: "urn:ietf:params:whip:ext" as defined in {urn-whip-subspace}.

For example, considering a potential extension of server-to-client communication using server-sent events as specified in https://html.spec.whatwg.org/multipage/server-sent-events.html#server-sent-events, the URL for connecting to the server side event resource for the published stream could be returned in the initial HTTP "201 Created" response with a "Link" header field and a "rel" attribute of "urn:ietf:params:whip:ext:example:server-sent-events". (This document does not specify such an extension, and uses it only as an example.)

In this theoretical case, the HTTP 201 response to the HTTP POST request would look like:

HTTP/1.1 201 Created
Content-Type: application/sdp
Location: https://whip.example.com/resource/id
Link: <https://whip.ietf.org/publications/213786HF/sse>;
      rel="urn:ietf:params:whip:ext:example:server-side-events"

5. Security Considerations

HTTPS SHALL be used in order to preserve the WebRTC security model.

6. IANA Considerations

This specification adds a new link relation type and a registry for URN sub-namespaces for WHIP protocol extensions.

6.2. Registration of WHIP URN Sub-namespace and WHIP Registry

IANA has added an entry to the "IETF URN Sub-namespace for Registered Protocol Parameter Identifiers" registry and created a sub-namespace for the Registered Parameter Identifier as per [RFC3553]: "urn:ietf:params:whip".

To manage this sub-namespace, IANA has created the "System for Cross-domain Identity Management (WHIP) Schema URIs" registry, which is used to manage entries within the "urn:ietf:params:whip" namespace. The registry description is as follows:

6.3. URN Sub-namespace for WHIP

WHIP Endpoint utilize URIs to identify the supported WHIP protocol extensions on the "rel" attribute of the Link header as defined in Section 4.7. This section creates and registers an IETF URN Sub-namespace for use in the WHIP specifications and future extensions.

6.3.1. Specification Template

Namespace ID:

  The Namespace ID "whip" has been assigned.

Registration Information:

  Version: 1

  Date: TBD

Declared registrant of the namespace:

  The Internet Engineering Task Force.

Designated contact:

   A designated expert will monitor the WHIP public mailing list, "wish@ietf.org".

Declaration of Syntactic Structure:

  The Namespace Specific String (NSS) of all URNs that use the "whip" Namespace ID shall have the following structure: urn:ietf:params:whip:{type}:{name}:{other}

  The keywords have the following meaning:

  - type: The entity type. This specification only defines the "ext" type.

  - name: A required US-ASCII string that conforms to the URN syntax requirements (see {{RFC8141}}) and defines a major namespace of a WHIP protocol extension. The value MAY also be an industry name or organization name.

  - other: Any US-ASCII string that conforms to the URN syntax requirements (see {{RFC8141}}) and defines the sub-namespace (which MAY be further broken down in namespaces delimited by colons) as needed to uniquely identify an WHIP protocol extension.

Relevant Ancillary Documentation:

  None

Identifier Uniqueness Considerations:

  The designated contact shall be responsible for reviewing and enforcing uniqueness.

Identifier Persistence Considerations:

  Once a name has been allocated, it MUST NOT be reallocated for a different purpose.
  The rules provided for assignments of values within a sub-namespace MUST be constructed so that the meanings of values cannot change.
  This registration mechanism is not appropriate for naming values whose meanings may change over time.

Process of Identifier Assignment:

  Namespace with type "ext" (e.g., "urn:ietf:params:whip:ext") is reserved for IETF-approved WHIP specifications.

Process of Identifier Resolution:

  None specified.

Rules for Lexical Equivalence:

  No special considerations; the rules for lexical equivalence specified in {{RFC8141}} apply.

Conformance with URN Syntax:

  No special considerations.

Validation Mechanism:

  None specified.

Scope:

  Global.

7. Acknowledgements

8. References

8.1. Normative References

[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC3264]
Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model with Session Description Protocol (SDP)", RFC 3264, DOI 10.17487/RFC3264, , <https://www.rfc-editor.org/info/rfc3264>.
[RFC3553]
Mealling, M., Masinter, L., Hardie, T., and G. Klyne, "An IETF URN Sub-namespace for Registered Protocol Parameters", BCP 73, RFC 3553, DOI 10.17487/RFC3553, , <https://www.rfc-editor.org/info/rfc3553>.
[RFC6750]
Jones, M. and D. Hardt, "The OAuth 2.0 Authorization Framework: Bearer Token Usage", RFC 6750, DOI 10.17487/RFC6750, , <https://www.rfc-editor.org/info/rfc6750>.
[RFC7064]
Nandakumar, S., Salgueiro, G., Jones, P., and M. Petit-Huguenin, "URI Scheme for the Session Traversal Utilities for NAT (STUN) Protocol", RFC 7064, DOI 10.17487/RFC7064, , <https://www.rfc-editor.org/info/rfc7064>.
[RFC7065]
Petit-Huguenin, M., Nandakumar, S., Salgueiro, G., and P. Jones, "Traversal Using Relays around NAT (TURN) Uniform Resource Identifiers", RFC 7065, DOI 10.17487/RFC7065, , <https://www.rfc-editor.org/info/rfc7065>.
[RFC7675]
Perumal, M., Wing, D., Ravindranath, R., Reddy, T., and M. Thomson, "Session Traversal Utilities for NAT (STUN) Usage for Consent Freshness", RFC 7675, DOI 10.17487/RFC7675, , <https://www.rfc-editor.org/info/rfc7675>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC8288]
Nottingham, M., "Web Linking", RFC 8288, DOI 10.17487/RFC8288, , <https://www.rfc-editor.org/info/rfc8288>.
[RFC8489]
Petit-Huguenin, M., Salgueiro, G., Rosenberg, J., Wing, D., Mahy, R., and P. Matthews, "Session Traversal Utilities for NAT (STUN)", RFC 8489, DOI 10.17487/RFC8489, , <https://www.rfc-editor.org/info/rfc8489>.
[RFC8725]
Sheffer, Y., Hardt, D., and M. Jones, "JSON Web Token Best Current Practices", BCP 225, RFC 8725, DOI 10.17487/RFC8725, , <https://www.rfc-editor.org/info/rfc8725>.
[RFC8829]
Uberti, J., Jennings, C., and E. Rescorla, Ed., "JavaScript Session Establishment Protocol (JSEP)", RFC 8829, DOI 10.17487/RFC8829, , <https://www.rfc-editor.org/info/rfc8829>.
[RFC8840]
Ivov, E., Stach, T., Marocco, E., and C. Holmberg, "A Session Initiation Protocol (SIP) Usage for Incremental Provisioning of Candidates for the Interactive Connectivity Establishment (Trickle ICE)", RFC 8840, DOI 10.17487/RFC8840, , <https://www.rfc-editor.org/info/rfc8840>.
[RFC8842]
Holmberg, C. and R. Shpount, "Session Description Protocol (SDP) Offer/Answer Considerations for Datagram Transport Layer Security (DTLS) and Transport Layer Security (TLS)", RFC 8842, DOI 10.17487/RFC8842, , <https://www.rfc-editor.org/info/rfc8842>.
[RFC8853]
Burman, B., Westerlund, M., Nandakumar, S., and M. Zanaty, "Using Simulcast in Session Description Protocol (SDP) and RTP Sessions", RFC 8853, DOI 10.17487/RFC8853, , <https://www.rfc-editor.org/info/rfc8853>.
[RFC8863]
Holmberg, C. and J. Uberti, "Interactive Connectivity Establishment Patiently Awaiting Connectivity (ICE PAC)", RFC 8863, DOI 10.17487/RFC8863, , <https://www.rfc-editor.org/info/rfc8863>.
[RFC9110]
Fielding, R., Ed., Nottingham, M., Ed., and J. Reschke, Ed., "HTTP Semantics", STD 97, RFC 9110, DOI 10.17487/RFC9110, , <https://www.rfc-editor.org/info/rfc9110>.
[RFC9143]
Holmberg, C., Alvestrand, H., and C. Jennings, "Negotiating Media Multiplexing Using the Session Description Protocol (SDP)", RFC 9143, DOI 10.17487/RFC9143, , <https://www.rfc-editor.org/info/rfc9143>.

8.2. Informative References

[I-D.draft-ietf-rtcweb-gateways]
Alvestrand, H. and U. Rauschenbach, "WebRTC Gateways", Work in Progress, Internet-Draft, draft-ietf-rtcweb-gateways-02, , <https://www.ietf.org/archive/id/draft-ietf-rtcweb-gateways-02.txt>.
[RFC3261]
Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", RFC 3261, DOI 10.17487/RFC3261, , <https://www.rfc-editor.org/info/rfc3261>.
[RFC6120]
Saint-Andre, P., "Extensible Messaging and Presence Protocol (XMPP): Core", RFC 6120, DOI 10.17487/RFC6120, , <https://www.rfc-editor.org/info/rfc6120>.
[RFC7826]
Schulzrinne, H., Rao, A., Lanphier, R., Westerlund, M., and M. Stiemerling, Ed., "Real-Time Streaming Protocol Version 2.0", RFC 7826, DOI 10.17487/RFC7826, , <https://www.rfc-editor.org/info/rfc7826>.
[RFC8141]
Saint-Andre, P. and J. Klensin, "Uniform Resource Names (URNs)", RFC 8141, DOI 10.17487/RFC8141, , <https://www.rfc-editor.org/info/rfc8141>.
[W3C.REC-webrtc-20210126]
Jennings, C., Ed., Boström, H., Ed., and J. Bruaroey, Ed., "WebRTC 1.0: Real-Time Communication Between Browsers", W3C REC-webrtc-20210126, W3C REC REC-webrtc-20210126, , <https://www.w3.org/TR/2021/REC-webrtc-20210126/>.

Authors' Addresses

Sergio Garcia Murillo
Millicast
Alexandre Gouaillard
CoSMo Software